![]() If the state of any channel short protect or overtemp changes, events will be triggered for the respective channel and state. Sonamp DSP 2-150 Mk II Das Herz jedes Sonance DSP Verstärkers ist ein leistungsfähiger 24bit/96k DigitalAnalogConverter der volle 4608 Kb Audiodaten pro Sekunde verarbeiten kann. The Channel Short Protect/Overtemp queries are sent to the unit approximately every 15 minutes once the system initializes. Automated polling routines are implemented in the attempt at keeping the variable information accurate as long as the DSP 8-130 is only controlled through the driver. Once the DSP 8-130 replies that it in on, the driver will then poll the individual groups for updating volume, input, and mute status variables. If the DSP 8-130 is powered off using the Master Power Off command, and is then turned back on using the Master Power On commands, the driver will continuously poll for accurate master power status. Master Power changes do not affect the Group Power variables being as the Group Power status cannot be polled for. Upon initialization, the Group Power Status variables will likely be out of sync, but as soon as any Group Power, or All Group Power commands are issued the Group Power Status variables should sync up for the respective group or all groups. The driver will attempt to keep the Group Power Status variables in sync with the system as long as the DSP 8-130 is only controlled through the driver. Group Power Status is not available according to the DSP 8-130 protocol documentation. The driver will initialize the Master Power Status, all available Group queries, and Channel Short Protect/Overtemp. Driver feedback and/or events are provided for Channel Name, Short Protect, and Overtemp only. Variables and events are not available for the All Group control commands. Driver commands are provided for All Groups. better dsp, better audio performance and analogue inputs for half the cost. Driver commands, variables, and/or events are provided for Group Name, Power, Input, Volume and Mute. Sonance DSP 2-150 Review (DSP Amplifier) Thread starter amirm Start date Aug. Driver commands, variables, and/or events are provided for Master Power. All channels to be used must be setup and assigned to Groups using the SONARC web page setup. This driver controls only the Group aspects of the Sonance DSP 8-130 amplifier. Input (1-4) Name - Enter the name to be used for Input (1-4). Convection cooled, fanless design allows for direct stacking with no air gap for even greater power density Class-D design is 93 efficient for maximum power output with minimal power usage. Compact form factor allows for space savings in the equipment rack with ample power to the speakers. Group (A-H) Name - Enter the name to be used for Group (A-H).Ĭhannel (1L-4R) Name - Enter the name to be used for Channel (1L-4R). Rated at 8 ohms, 4 ohms & stable into 2 ohms. SONAMP MULTI-CHANNEL POWER AMPLIFIER WITH SonARC V2. The default TCP port of the DSP 8-130 is port 52000. View and Download Sonance DSP 2-150 MKII instruction manual online. TCP Port - Enter the network port to use for TCP control. It is recommended the DSP 8-130 be set to use a static IP address either via the SONARC web page or MAC reservation in the network router. TCP Address - Enter the IP address of the DSP 8-130. It has not been tested with the DSP 2-150 or DSP 2-750, but all three models utilize the same protocol with the limitation being how many groups, channels, and input sources are available.ġ.01ğixed issue when loading into ID APEX This driver was developed and tested using a Sonance DSP 8-130 with firmware version 2.50. Sonamp DSP amplifiers prepare your audio system for what’s next.This driver is for controlling the Sonance DSP 8-130 Amplifier. Most amplifiers have processing limitations that constrain the audio output, and limit the maximum amount of pass through information to 1411 Kbps which compromises the quality of the listening experience.The new line of Sonamp DSP amplifiers enables listeners to enjoy the full clarity and output of whatever audio passes through, from MP3 to full High Resolution Audio. Ready for the future of high-resolution audioĪt the core of every DSP amplifier is a powerful 24 bit/96K DAC, capable of handling a full 4608 Kbps of audio data. Additionally, should there be a need for further customization, SONARC provides a 10-band parametric EQ to optimize sonic performance in any space. See More Details about 'Sonance SONAMP DSP 2-750 MKII Power Amplifier - Black. The presets enable effortless DSP without the need for additional hardware, software, and more importantly time. 315.00 + 43.60 shipping + 43.60 shipping + 43.60 shipping. The new line of DSP amplifiers feature SONARC (Sonance Advanced Room Correction), which offers hundreds of EQ presets designed specifically for Sonance speakers available through simple pull down menus.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |